3. B I N G K R E I D L E R C A R B S
10 or 12mm clamp size 16mm
Late 1970’s Kreidler Flory MP-9 and MP-19 mopeds are US models, 30mph (2.0hp), with Bing 1/12/260 (12mm) carbs. Other Flory models in Europe are 25kmh (17mph) with Bing 1/10/126 (10mm) carbs. The “bell” outer diameter is 54mm, same as the Solo Bing below.
# qty Kreidler# price description
1a 1 215.19.99a N/A carburetor 1/12/260 has metal-tip needle, no-slot float
1b 1 215.19.99b N/A carburetor 1/12/268 has rubber-tip needle, slotted float
2a 1 07.15.08 $6.00 clamp screw M5 x 15 thin shank (clamp size 16)
3a 1 07.16.06 N/A float no slot substitute slotted float & rubber needle
3b 1 07.16.06b $15.0 float with slot for rubber tip needle
4a 1 07.15.44 $39.0 float needle metal for no slot float
4b 1 07.15.44b $15.0 float needle rubber for slotted float
5 1 607.15.1 $4.00 hinge pin (Bing Puch 19)
6 1 07.15.05 $8.00 float bowl (Bing Puch 21)
7 1 07.15.32 $3.50 ring seal (Bing Puch 22)
8 1 07.16.20 $15.0 needle jet 2.17 (Bing Puch 2b)
9 1 07.15.41 none 3.5mm main jet #68
10 1 07.15.12 $18.0 needle 2-mark 36mm (Bing Puch 4a)
11 1 07.15.15 $12.0 fuel inlet vertical type M8x0.75
11 1 07.15.15s $20.0 fuel inlet swivel type Puch 24+25+26
12 1 07.15.21 $15.0 fuel strainer (Bing Puch 27)
13 2 07.15.25 $1.00 fuel inlet seal washer M8
14 1 07.15.14 $3.00 idle screw M5-0.8 (Bing Puch 16)
15 1 07.15.22 $3.00 idle screw spring (Bing Puch 17)
16 1 07.15.99 $35.0 slide Ø14.5 #10 says “10 B”
17 1 07.15.18 $3.00 clip for needle (Bing-Sachs 6)
18 1 07.15.55 $3.00 disk washer (Bing-Sachs 7)
19 1 07.15.23 N/A slide spring Ø11 x 42
20 1 07.16.25 N/A carb top cover smaller than Puch
21 2 07.16.23 $1.50 carb top screw (Bing Puch 10)
22 1 07.16.12 N/A choke rod 35mm (use 38mm Bing-Puch 33)
22 1 07.16.12s $4.00 choke rod substitute 38mm
23 1 07.16.13 N/A push button goes on top of choke rod, not needed
24 1 07.15.27 N/A top gasket smaller than Puch
25 1 07.15.20 $20.0 choke slide 14 wide, can grind down a Puch one